电缆作为电力传输的主要装备，一旦爆发故障，就会导致电力网的电力中止，从而严重住民生涯和企业生产。并且古板的电缆故障检测要领，较量费时艰辛。 地埋探测的方法大大提高了电缆故障的检测事情，因此获得了普遍的应用。

As the main equipment of power transmission, once the cable fails, it will lead to the power interruption of the power network, which will seriously affect the residents' life and enterprise production. Moreover, the traditional cable fault detection method is time-consuming and laborious. The method of buried detection greatly improves the detection of cable faults, so it has been widely used.

凭证基本的测试办法操作。先要相识故障爆发的缘故原由及电缆基本情形，例如是运行爆发故障照旧预试爆发故障，是新电缆照旧运行时间很长的电缆，电缆的或许长度，电缆中心有没有讨论，电缆以前有没有泛起过故障，电缆是直埋照旧在电缆沟铺设，以及电缆类型等等。其次一定要搞清晰，电缆两头必需与其它线路断开，确保电缆无电，电缆周围情形处于状态。

Follow the basic test steps. First of all, we should understand the causes of the fault and the basic situation of the cable, such as whether the fault is caused by operation or pre-test, whether it is a new cable or a cable that has been running for a long time, the approximate length of the cable, whether there is a joint in the middle of the cable, whether the cable has failed before, whether the cable is directly buried or laid in the cable trench, and the type of cable, etc. Secondly, it must be clear that both ends of the cable must be disconnected from other lines to ensure that the cable has no electricity and the surrounding environment of the cable is in a safe state.

另外在，每次与电缆接线前，将电缆各相线与地用短蹊径毗连放电，放电时必需先将短蹊径一端接地，另一端划分接电缆各相线放电。关于其它电器，例如电容器，试验变压器等，接线及去掉毗连线前也要注重先放电，后接线。

In addition, before each connection with the cable, connect each phase line of the cable to the ground with a short line for discharge. When discharging, one end of the short line must be grounded first, and the other end must be connected to each phase line of the cable for discharge. For other electrical appliances, such as capacitors, test transformers, etc., pay attention to discharge before wiring and removing the connecting wire.

在装备测试电缆时，必需先用闪测仪低压脉冲功效，对电缆各相划分举行全长测试，看三相对铠装测试时，测试波形是否一致。对大部分高阻故障，各相测试波形是一致的。对低阻故障以及保存断相故障的高阻故障，故障相测试波形与测试的电缆全长就纷歧致，这样就可以直接用低压脉冲测试出故障距离。

When the equipment tests the cable, it must first use the low-voltage pulse function of the flash tester to test the full length of each phase of the cable respectively to see whether the test waveform is consistent when the three-phase pair armor is tested. For most high resistance faults, the test waveforms of each phase are consistent. For low resistance fault and high resistance fault with open phase fault, the test waveform of fault phase is inconsistent with the total length of the tested cable, so the fault distance can be directly measured with low-voltage pulse.

故障测试问题分为测试职员及装备。测试职员要注重仪器的接地和放电，装备主要是准确接线，可以凭证相关说明书举行相识操作。

The safety problems of fault testing are divided into the safety of testers and the safety of equipment. The safety of testers should pay attention to the grounding and discharge of the instrument. The safety of equipment is mainly the correct wiring, which can be understood and operated according to the relevant instructions.

以上就是今天为各人先容的关于问题以及注重事项的所有内容，希望对各人能有所资助，想要相识更多内容可以电话联系Yp街机电子游戏或者关注我们的网站，我们的事情职员会实时与您取得联系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website , our staff will contact you in time.